top of page
Simon Ogier

Simon Ogier

CTO, Smartkem

Simon Ogier spoke at MicroLED Connect in 2024 and 2025, representing Smartkem.



High yield electrical connections to micro-LEDs via the chip-first OTFT backplane process

Talk · 24 September 2025

→ See the MicroLED Connect & AR/VR Connect 2025 agenda

Fabrication of micro-LED displays with high yield and a minimal requirement for re-work is an important pre-condition for successful commercialisation of the technology. Economic production of micro-LED displays also requires the die size to be reduced to dimensions much smaller than has been used for mini-LED displays. This size reduction presents challenges in the attachment of the microscopic dies to active matrix driving systems. Eutectic bonding of micro-LEDs to pads on the backplane commonly requires low melting point metals to be used such as indium or tin, with processing of these materials by difficult to scale processes of thermal evaporation and lift-off. An alternative to eutectic bonding is presented here which reverses the fabrication process, starting with the micro-LED chip first where the anode/cathode pads of the flip-chip device are facing upwards. A planarization layer of organic polymer is formulated and coated on top of the die to provide a level surface and then patterned to form via holes over the pads. Metallization down the vias by sputtering then create ohmic contacts to the anode/cathode pads. This process has been shown to have extremely high die light on yields due to the conventional via process used to make the connection. Active matrix driving of chip-first connected displays requires the use of TFT with low processing temperatures. This is due to the micro-LED sensitivity to elevated temperatures potentially caused by migration of metal atoms into the quantum well structures. Organic Thin-Film Transistors (OTFT) can be processed at 150°C and has been shown to be a suitable TFT technology for driving micro-LED. This presentation describes the potential for micro-LED device manufacturing using the chip-first approach and the types of display that OTFT may be suitable for in first-generation products.



Chip-first active-matrix fabrication approach for effective connection of TFT backplanes to micro-LEDs

Talk · 26 September 2024

→ See the MicroLED Connect 2024 agenda

Micro-LEDs are a major advancement in visual display technology, offering high brightness, efficiency, and long lifespan. However, their high cost stems from low-yield fabrication processes that struggle to reliably connect millions of microscopic LEDs to the display backplane. Faulty pixel identification, repair strategies, and dual redundancy have enabled the production of working displays with superior image quality due to their high dynamic range. However, inspection only identifies issues; it doesn’t resolve them, and repair costs time and money. Therefore, there is a need to enhance micro-LED fabrication quality through innovative processes. This presentation introduces a chip-first strategy, where micro-LEDs are placed face down on a substrate with contact pads facing upwards. A pre-polymer layer is spin-coated, patterned, and cured to form via hole connections above the anode and cathode pads. A metal layer is then sputtered and patterned to connect the LEDs, without using eutectic bonding or laser sintering. Organic thin-film transistor (OTFT) materials are applied in multiple layers using conventional tools, yielding a high-quality display through low-temperature processes (<150°C). The low temperature prevents damage to micro-LEDs, is eco-friendly by using less energy, and allows the use of a wider range of transparent plastic substrates with better optical qualities. The lowest temperature tested so far is 80°C. The presentation will show the structure of the chip-first backplane and its corresponding cross-sectional structure. OTFT transfer curves and an image of the 100x180 monochrome 2.2” display are also presented. Turn-on yield of the wired-up micro-LEDs is high, with no failures detected in over 18,000 devices.



Connect with Simon Ogier on LinkedIn ↗

← All MicroLED Connect speakers

© 2026 Powered by MicroLED Association & TechBlick

KGH Concepts GmbH | Mergenthalerallee 73-75, 65760, Eschborn, Germany | VAT number: DE 337022439 | +49 17661704139

  • LinkedIn
bottom of page